09/2008 awt6302r pcs/cdma 3.4v/28dbm linear power amplifer module data sheet - rev 2.1 m9 package 8 pin 3 mm x 3 mm x 1.1 mm surface mount module figure 1: block diagram features ? ingap hbt technology ? high effciency: 39%, v mode = 0 v 40%, v mode = +2.85 v (no mode switching) ? low quiescent current: 50 ma ? low leakage current in shutdown mode: <1 a ? v ref = +2.85 v (+2.75 v min over temp) ? optimized for a 50 ? system ? low profle miniature surface mount package: 1.1 mm ? cdma 1xrtt, 1xev-do compliant ? pinout enables easy phone board migration from 4 mm x 4 mm package ? rohs-compliant package, 250 o c msl-3 applications ? cdma/evdo pcs-band wireless handsets and data devices product description the awt6302r meets the increasing demands for higher effciency and linearity in cdma 1x handsets, while reducing pcb area by 44%. the package pinout was chosen to enable handset manufacturers to switch from a 4 mm x 4 mm pa module with very few layout changes to the phone board. the pa module is optimized for v ref = +2.85 v. the device is manufactured on an advanced ingap hbt mmic technology offering state-of-the-art reliability, temperature stability, and ruggedness. selectable bias modes that optimize effciency for different output power levels, and a shutdown mode with low leakage current, increase handset talk and standby time. the self-contained 3 mm x 3 mm x 1.1 mm surface mount package incorporates matching networks optimized for output power, effciency, and linearity in a 50 ? system. bias control v cc v ref rf in rf out gnd v mode 1 7 5 8 6 gnd at slug (pad) 3 4 2 v cc gnd
2 data sheet - rev 2.1 09/2008 302 fire 2: pinot (ray op vie) abe 1: pin esription v cc rf out v ref rf in v mode gnd v cc gnd 1 gnd 2 8 7 gnd 6 5 3 4 1 v cc supply voltage 2 rf in rf input 3 v mode mode control voltage 4 v ref reference voltage 5 gnd ground 6 gnd ground 7 rf out rf output 8 v cc supply voltage
data sheet - rev 2.1 09/2008 awt6302r 3 electrical characteristics table 2: absolute minimum and maximum ratings stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. table 3: operating ranges the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defned in the electrical specifcations. notes: (1) for operation at v c c = +3.2 v, p o u t is derated by 0.5 db. parameter min max unit supply voltage (v ) mode control voltage (v mode ) reference voltage (v ref ) rf input power (p in ) storage temperature (t stg ) parameter min typ max unit comments operating frequency (f) mhz supply voltage (v ) reference voltage (v ref ) pa "shut down" mode control voltage (v mode ) high bias mode rf output power (p out ) (1) case temperature (t )
4 data sheet - rev 2.1 09/2008 302 table 4: electrical specifcations ? notes: 1. acprs and effciency limits at mid-band only. ain 24.5 22 24.5 29 27 db p 287 = +28 dbm, v 02( = 0 v p 287 %p9 02( = +2.85 v mdd3r at + 0+rv 3lpdd% 0+ mdd% + - - -51 -51 -47 -47 % p 287 = +28 dbm, v 02( = 0 v p 287 %p9 02( = +2.85 v mdd3r at + 0+rv 3lpdd% 0+ mdd% + - - -57 -57 % p 287 = +28 dbm, v 02( = 0 v p 287 %p9 02( = +2.85 v 3r(ll 37 8.3 39 9 - - % p 287 = +28 dbm, v 02( = 0 v p 287 %p9 02( = +2.85 v 4lv, - 50 ma v 02( = +2.85 v 5 - 2.3 4 ma r9 5( pin, pa "on" 0rrr - 0.3 1.0 ma r9 02( pin, v 02( = +2.85 v /dd - 5 a v cc = +4.2 v, v 5( = 0 v, v 02( = 0 v 1rlvl5l%d - -132 -130 %p+ 0+r0+ +dprlv r rr - - -40 -55 -30 -30 % ,s,psd - - 95 slrv2s/ dvslrvrsv - - % p 287 +28 dbm ,drd95 2rdrd95 sslvrdrsdldv /rdplvpdvvvlr spdddlrrdl - - 95 sslvrrsdld
data sheet - rev 2.1 09/2008 awt6302r 5 table 5: electrical specifcations (t c = +25 c, v cc = +3.4 v, v ref = +2.85 v, v mode = +2.85 v, 50 ? system) notes: 1. acprs and effciency limits at mid-band only. parameter min typ max unit comments dl 24 22 24.5 28 27 db p 287 = +28 dbm p 287 gp gmdfhw&kdho3rhu at + 0+riivhw 3ulpdu&kdho:0+ gmdfhw&kdho: n+ - - -52 -51 -47 -47 gf p 287 = +28 dbm p 287 gp gmdfhw&kdho3rhu at + 0+riivhw 3ulpdu&kdho:0+ gmdfhw&kdho: n+ - - -57 -57 gf p 287 = +28 dbm p 287 gp 3rhugghg(iilflhf 37 8.3 40 9 - - p 287 = +28 dbm p 287 gp 4xlhvfhw&xuuhw,ft - 48 ma v 02( = +2.85 v 5hihuhfh&xuuhw - 2.3 4 ma wkurxk9 5() pin, pa on 0rgh&rwuro&xuuhw - 0.3 1.0 ma wkurxk9 02( pin hdndh&xuuhw - 5 a v cc = +4.2 v, v 5() = 0 v, v 02( = 0 v 1rlvhl5hfhlyhdg - -132 -130 gp+ 0+wr0+ +duprlfv ir irir - - -40 -55 -30 -30 gf ,sxw,pshgdfh - - 96:5 6sxulrxv2xwsxwhyho doovsxulrxvrxwsxwv - - gf p 287 +28 dbm ,edgordg96:5 2xwriedgordg96:5 ssolhvryhudoorshudwludhv rdgplvpdwfkvwuhvvlwkr shupdhwghudgdwlrruidloxuh - - 96:5 ssolhvryhuixoorshudwludh
6 data sheet - rev 2.1 09/2008 awt6302r application information to ensure proper performance, refer to all related application notes on the anadigics web site: http://www.anadigics.com shutdown mode the power amplifer may be placed in a shutdown mode by applying logic low levels (see operating ranges table) to both the v ref mode voltages. table 6: bias control bias modes the power amplifer may be placed in either a low bias mode or a high bias mode by applying the appropriate logic level (see operating ranges table) to the v mode voltage. the bias control table lists the recommended modes of operation for various applications. figure 3: application circuit application p out levels bias mode v ref v mode cdma - low power < +16dbm cdma - high power >+16 dbm high shutdown shutdown rf in 6 ref rf in mode gnd gnd rf out vmode 2.2f rf out 0.01f f vref 1000 pf c6 68 pf 1000 pf gnd at slug
data sheet - rev 2.1 09/2008 awt6302r 7 package outline figure 4: m9 package outline - 8 pin 3 mm x 3 mm x 1.1 mm surface mount module figure 5: branding specifcation 6302r llllnn
8 data sheet - rev 2.1 09/2008 302 pnn pn abe : ape ee iensions fire : ape ee paain p p p p p p 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7"
data sheet - rev 2.1 09/2008 awt6302r 9 notes
warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. important notice anadigics, inc. 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com e-mail: mktg@anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.1 09/2008 10 awt6302r ordering information order number temperature range package description component packaging AWT6302RM9Q7 rohs-compliant 3 mm x 3 mm x 1 mm surface mount module tape and reel, 2500 pieces per reel
|
